KonxisEngineering
Konxis Engineering · India

Engineering analysis for difficult mechanical problems

When a product fails, a simulation is inconclusive, or a design needs stronger evidence before release, the engineering problem is rarely just “run an FEA.”

We help engineering teams understand what is physically controlling the problem, what evidence is needed, and what should change as a result.

Failure investigation · Advanced structural analysis · Verification & validation · Design improvement

01 · Physical system Component in service Load Load 02 · Engineering question Which load or detail actually governs? Not: which solver 03 · Model F1 F2 Load path · contact · constraint 04 · Evidence Measured point Response vs. measurement 05 · Decision Limit Accept / change Design · limit · inspection The figure moves left to right: evidence is produced, then a decision is taken. The model exists to serve the decision. Chain of reasoning System → question → model → evidence → decision

Fig. 01 — From engineering question to decision

Section 02 — Where we are useful

When routine engineering is not enough

Some problems look simple until the real behaviour is examined.

A component may pass a static stress check and still crack in service.
A machine may be strong enough but unable to operate through its required speed range.
A simulation may converge but still represent the wrong load path.
A design may work in principle but lack enough evidence for confident release.

These are the problems where deeper engineering judgement matters.

A · A product is failing

Cracks, deformation, leakage, unexpected movement, vibration or premature damage.

Failure Investigation & Root Cause

We investigate the physical mechanism behind the failure and identify what needs to change.

Investigate a Failure

B · A design needs proof

The model looks reasonable, but the engineering decision still carries uncertainty.

Verification & Validation

We assess assumptions, model behaviour, sensitivity and available test evidence to establish how much confidence the analysis deserves.

Validate a Design

C · A product needs improvement

The design needs more strength, longer life, lower mass, better performance or greater operating margin.

Analysis-led Design Improvement

We use engineering analysis to identify where the design can change — without adding complexity or material where it is not needed.

Improve a Product

Section 03 — Method

We do not begin by choosing a solver.

We begin by asking:

What is the engineering question?

Then we determine what level of analysis and evidence is actually justified.

Section 04 — Problem areas

What we actually help solve

Our work is organised around engineering problems, not software packages.

01

Structural failure & root cause

Recurring cracks, unexpected deformation, overloaded components, failed joints and unclear load paths.

Crack Load path Detail Failure & root cause
02

Fatigue & damage tolerance

Welded structures, cyclic loading, crack growth, defects and questions about remaining serviceability.

Δσ limit Cycles → Fatigue & damage tolerance
03

Buckling & stability

Thin structures, shells, booms, pressure vessels and components where instability may govern before conventional strength limits.

Mode 1 P cr Amplitude → Buckling & stability
04

Vibration & dynamics

Resonance, excessive operating vibration, rotating machinery, structural dynamics and restricted operating speed ranges.

Resonance Frequency → Vibration & dynamics
05

Impact & transient loading

Drop events, crash structures, containment, high-rate loading and problems where inertia and contact change the response.

F peak Time → Impact & transient
06

Complex structural behaviour

Contact, preload, material nonlinearity, large deformation, thermal effects and other situations where simple linear assumptions may not be enough.

Contact Preload · large deformation Complex behaviour

Explore Engineering Capabilities

Section 05 — Method

Engineering before simulation

Good analysis begins before the solver is opened.

Hover a stage to read what it involves.

01

Understand

Understand the product, operating conditions, requirements and what is going wrong.

02

Define

Turn the problem into measurable questions and a clear analysis objective.

03

Model

Represent the relevant geometry, materials, loads, contacts and constraints.

04

Verify

Check assumptions, numerical behaviour, convergence and sensitivity.

05

Validate

Where appropriate, compare predictions with testing, measurements or other credible reference data.

06

Decide

Turn the technical result into a design change, operating limit, inspection requirement, test plan or engineering conclusion.

Fig. 02 — Engineering question → model → evidence → decision

The objective is not the most complicated model.
It is a model and evidence base that are appropriate for the decision.
Section 06 — Principles

Built around engineering judgement

Five principles that decide how the work is done — and how far the analysis should be taken.

They are the reason the method is chosen around the physics and the decision, rather than around a particular solver.

Meet the team

P1

Specialist, not generic

We focus on difficult structural and mechanical problems where specialist analysis can add value.

P2

Physics before method

We use nonlinear, dynamic, fatigue, stability or other advanced methods when the physical problem requires them — not simply because they are available.

P3

Analysis connected to reality

Recommendations consider loads, materials, manufacturing, assembly, operating conditions and practical product constraints.

P4

Verification is part of the engineering

Model assumptions, boundary conditions, convergence, sensitivity and validation are considered as part of the work rather than added at the end.

P5

Direct technical involvement

Konxis is deliberately specialist. The engineers who understand the problem are directly involved in the analysis and technical discussion.

Section 07 — Sectors

Where we can help

We work with engineering-intensive companies where mechanical performance, reliability or validation matters.

F Torque Machine frame · load introduction Weldment detail
01

Industrial Equipment & Machinery

Machine structures, process equipment, material-handling systems, fabricated structures, pressure-containing components and mechanical assemblies.

Structural performance · Fatigue · Nonlinear behaviour

Industrial equipment

Mount Chassis rail · weld detail · durability
02

Automotive & Mobility

Structural components, chassis-related systems, commercial vehicles, off-highway equipment and durability problems.

Automotive & mobility

Skin Rib · stringer · fastener pattern
03

Aerospace & Advanced Structures

Structural analysis, verification, composites, lightweight structures and technically demanding engineering assessments.

Relevant team experience

Aerospace capability is informed by professional experience in aerospace structural engineering. Previous professional experience is clearly separated from work performed by Konxis.

Aerospace & advanced structures

Duty load Chassis Frame · suspension · weld fatigue
04

Heavy Equipment, Mining & Energy

Large structures, fatigue, vibration, stability, impact and service-life problems.

Heavy equipment, mining & energy

The industry may change.
The engineering questions often do not.
Section 08 — Selected investigations

Selected Engineering Investigations

Selected studies demonstrating how engineering analysis can clarify complex structural, dynamic and fatigue-related problems.

Industrial Machinery / Packaging Automation Synthetic Engineering Study

High-Speed Cam–Follower Redesign

A spring-return cam–follower mechanism was investigated for an increase from 200 to 260 rpm. A reduced-order model predicted contact loss in the original configuration; redesign screening produced calculated nominal and worst-corner contact-force margins of +36.17 N and +16.26 N within a synthetic uncertainty envelope.

Automotive / Powertrain / Engine Accessories Literature-Informed Reconstruction

Beyond Static Strength

A literature-informed investigation of alternator mounting bracket fatigue, considering engine-induced cyclic stress, local notch severity and surface condition. An integrated redesign produced a calculated equivalent fatigue-demand indicator of 138.7 MPa against an illustrative baseline of 234.7 MPa under declared assumptions.

Each study is labelled by evidence status. Calculated results are not presented as measured outcomes.

Section 09 — Evidence

Evidence before confidence

A model can converge perfectly and still represent the wrong physical problem. We make the boundary between assumption and evidence visible.

Assumed input Used to construct a synthetic study or preliminary model.
Calculated result An independently reproducible analytical or reduced-order calculation.
Simulation result A numerical prediction from a defined model.
Measured result Evidence obtained from a physical component, test or operating system.
Validated result A prediction that has been compared against appropriate independent evidence.
Released design A result accepted against the responsible engineering standard, test basis and project requirements.

Confidence increases as independent evidence increases.

Not every project reaches the final rung. Stating where a result actually sits is part of the engineering.

Section 10 — Team

A team of engineers.
Specialist perspective.

Engineers reviewing dimensioned mechanical drawings and component detail sketches together at a work table.

Konxis Engineering · engineering analysis team

Education Master's degrees in Engineering — including IIT Bombay
Professional background Aerospace, automotive and industrial engineering teams

Konxis is a team of engineers, not a single practitioner. Several members hold a Master's degree in Engineering from IIT Bombay, and between them team members have worked with established manufacturers and suppliers across these sectors. Collectively, that background covers structural analysis, verification and validation, failure analysis, composite structures, material behaviour, and nonlinear and dynamic problems.

Konxis is intentionally small and specialist. That means clients work directly with the engineers responsible for understanding the problem, developing the analysis and interpreting the result.

Distinction

Team academic and professional background is clearly separated from work performed by Konxis. The first is background and training; the second is the work this practice performs for its clients. Individual client engagements and client names are not published.

Section 11 — Engaging

A practical way to start

You do not need to know which simulation method you need before contacting us.

A project can begin with a focused engineering discussion or diagnostic assessment.

01

Focused Engineering Project

For a defined technical question.

Failure investigation · Structural assessment · Advanced analysis · Design verification

02

Product Development Support

For companies developing or improving a product.

Design · Simulation · Redesign · Prototype support · Validation

03

Specialist Engineering Support

For internal engineering or CAE teams that need additional technical capability.

Specialist analysis · Independent review · CAE support · Design and engineering support

The engagement can start small and become more detailed only when the evidence shows that it is necessary.

Discuss Your Engineering Problem

Section 12 — Insights

Engineering insights

Practical articles on analysis, failure investigation and verification — including when advanced simulation is necessary, when it is not, and how to tell whether an engineering result can actually be trusted.

Explore Engineering Insights

Section 13 — Contact

Have a difficult engineering problem?

A component is failing.
A simulation does not agree with reality.
A design needs independent technical assessment.
A machine cannot operate through its required range.
Or an engineering team needs specialist analysis to make a decision.

Intake

Tell us what is happening and what decision you need to make. You do not need to know which analysis method you need — that is our judgement to make with you.

Start with the engineering question.

Konxis Engineering
Advanced engineering analysis for difficult mechanical problems.
Working across India.