Engineering analysis for problems that are difficult to answer with routine methods
When a product is failing, a simulation is inconclusive, a design is close to its limit, or an engineering team needs confidence before making a change, the first question is not “Which software should we use?”
It is: what do we need to understand or prove?
Konxis Engineering helps manufacturers and engineering teams answer difficult mechanical questions through failure investigation, structural analysis, verification and validation, dynamics, and analysis-led product improvement.
The method is chosen around the physics and the decision — not around a particular solver.
What can we help you solve?
Most engineering engagements start with one of these situations.
A product is failing
Cracks, unexpected deformation, premature damage or repeated component failures need more than a stress plot.
We investigate the physical failure mechanism, reconstruct the relevant loading and load path, test possible causes and identify what needs to change.
Typical problems
- Fatigue cracking · Structural failure · Unexpected yielding
- Deformation · Joint problems · Load-path issues
An analysis result is difficult to trust
The model runs, but the result does not give the team enough confidence to make a decision.
We review the engineering question, assumptions, loads, constraints, material behaviour, mesh, numerical response and available evidence to establish what the analysis can — and cannot — support.
Typical problems
- Unexpected FEA results · Poor correlation with test · Model review
- Convergence concerns · Uncertain boundary conditions · Conflicting results
A design needs to perform better
A product may need to be lighter, stronger, more durable, more stable or more reliable without simply adding material.
We use analysis to understand which part of the design is limiting performance and then develop practical design changes that can be manufactured and verified.
Typical problems
- Weight reduction · Strength improvement · Durability
- Structural redesign · Manufacturability · Performance improvement
Six areas of specialist work
Each begins with the engineering question, not the method.
Failure & Root-Cause Engineering
Understand why the product failed before deciding how to fix it.
A broken component contains evidence about what happened. The useful question is not simply where it broke, but why the failure occurred under the actual operating conditions.
We combine engineering evidence, mechanics and simulation to investigate competing explanations and identify the mechanism that needs to be addressed.
We can help with
- Failure mechanism assessment
- Structural failure investigation
- Fatigue and crack initiation assessment
- Load-path reconstruction
- Joint and attachment problems
- Unexpected yielding or deformation
- Material behaviour assessment
- Simulation-assisted root-cause analysis
- Corrective design recommendations
- Verification planning for the proposed fix
Useful when
A component has failed repeatedly, a redesign has not solved the problem, or the physical evidence and existing analysis do not agree.
Advanced Structural Analysis
Use the simplest model that can answer the question — and add complexity only when the physics requires it.
Not every problem needs nonlinear FEA. But some problems cannot be answered reliably with a simple linear model.
We select the analysis approach according to the behaviour that matters: contact, plasticity, large deformation, instability, cyclic loading, impact, vibration or other nonlinear effects.
Analysis areas include
- Linear and nonlinear structural analysis
- Large deformation and material nonlinearity
- Contact and assembly behaviour
- Static and quasi-static loading
- Explicit dynamics and impact
- Buckling and structural stability
- Fatigue assessment
- Fracture mechanics and crack-growth assessment
- Damage tolerance
- Modal and vibration analysis
- Multibody dynamics
- Fluid-structure interaction where the engineering problem requires it
Useful when
Routine calculations cannot explain the observed behaviour, a design operates close to a structural limit, or the physical response involves interactions that simpler methods cannot capture.
Verification & Validation
Make the analysis useful enough to support a decision.
A model producing a result is not the same as a model producing a trustworthy engineering result.
Verification examines whether the analysis has been set up and solved correctly. Validation asks whether the model represents the real system adequately for its intended use. The level of work required depends on what the model will be used to decide.
This approach is consistent with established computational V&V practice, including ASME's V&V framework for computational solid mechanics.
We can help with
- Defining what the analysis needs to establish
- Analysis and modelling strategy
- Geometry and model checks
- Boundary-condition review
- Material-model assessment
- Mesh and convergence assessment
- Numerical and physical sanity checks
- Sensitivity studies
- Uncertainty assessment where appropriate
- Comparison with test or other credible reference data
- Test-to-analysis correlation
- Independent technical review
- Engineering interpretation of results
Useful when
A simulation is being challenged in a design review, analysis and test disagree, an internal CAE result needs independent review, or a model is being used for a decision with significant technical consequences.
Fatigue, Damage Tolerance & Structural Life
Understand how a structure behaves over its actual service life.
A component does not necessarily fail because of its highest single load. Repeated loading, stress concentration, weld details, crack growth and the sequence of operating conditions can determine the real damage accumulation.
We assess the mechanisms that control structural life and help translate them into design, inspection or operating decisions.
We can help with
- Fatigue assessment
- Welded-structure fatigue
- Stress-life and strain-life approaches where appropriate
- Load-spectrum assessment
- Crack-growth analysis
- Damage tolerance
- Residual strength assessment
- Inspection and maintenance basis
- Sensitivity to load, material and flaw assumptions
- Design changes to improve fatigue life
Useful when
A component develops recurring cracks, service life is shorter than expected, a structure needs an inspection strategy, or a design change needs to be assessed for durability.
Dynamics, Vibration & Stability
Find out what is limiting the machine or structure before changing it.
Vibration problems are often not solved by simply making a component stiffer. The real issue may involve excitation, structural modes, damping, operating speed, joint behaviour, tool dynamics or the interaction between several parts of the system.
Similarly, a buckling load from a simplified eigenvalue calculation is not automatically the real stability limit. We investigate the behaviour that controls the operating envelope.
We can help with
- Modal analysis
- Frequency-response assessment
- Resonance investigation
- Structural dynamics
- Vibration root-cause analysis
- Operating-condition assessment
- Stability and buckling
- Nonlinear buckling and post-buckling where required
- Sensitivity to imperfections, restraints and load path
- Dynamic design improvements
- Correlation with measured vibration or test data
Useful when
A machine has an unexplained vibration, an operating speed is restricted, a structure is approaching instability, or a calculated natural frequency does not match what is observed in service.
Composite, Material & Product Engineering
Connect material behaviour to the structure and the product.
Material properties cannot always be treated as generic inputs. Composite lay-up, material direction, nonlinear behaviour, temperature, loading rate and available test data can all influence the answer.
We work with material and structural behaviour together, particularly where the material response is important to the engineering decision.
We can help with
- Composite structural analysis
- Laminate and sandwich structures
- Material behaviour assessment
- Constitutive model selection
- Material-model development and calibration
- Failure-criteria assessment
- Material substitution studies
- Structural interpretation of material behaviour
- Mechanical design and redesign
- Weight reduction
- Tooling and fixture design
- Design-for-manufacturing considerations
- Prototype and design-validation support
Useful when
A material is being changed, a composite structure behaves differently from expectation, an existing product needs redesign, or a structural improvement must remain practical to manufacture.
From engineering problem to engineering decision
We do not start with the solver. A strong engineering analysis is a chain of decisions.
Fig. 02 — Engineering question → model → evidence → decision
What you receive
The deliverable depends on the problem, but typically includes some combination of the following.
- Engineering assessment and conclusions
- Analysis models and results
- Key assumptions and limitations
- Load and boundary-condition basis
- Sensitivity or convergence evidence where relevant
- Failure mechanism assessment
- Design recommendations
- Fatigue or damage assessment
- Test or correlation plan
- Validation evidence where available
- Engineering drawings or design-change recommendations where in scope
- Technical report suitable for internal engineering review
The aim is to leave your team knowing what the analysis means, what it does not mean, and what should happen next.
When you already have an internal CAE team
You do not need to outsource an entire engineering function to use specialist support.
Konxis can work alongside an existing engineering or CAE team when you need:
A second technical perspective on a difficult model, result or design decision.
Support for problems that require nonlinear structural analysis, fatigue, damage tolerance, dynamics, stability or other specialist methods.
Extra support before a design review, prototype build, test campaign or development milestone.
An independent investigation when an internal team needs to step outside the normal development workflow and understand why something failed.
Support from identifying the limiting mechanism through to evaluating practical design changes.
The level of analysis should match the decision
Not every engineering question needs a high-fidelity simulation. Sometimes a hand calculation or simplified model is the right answer. Sometimes the problem requires nonlinear FEA, dynamics, fatigue analysis or physical testing.
We choose the level of analysis according to the question, the available evidence and the consequence of the decision.
That is how we avoid both under-analysis and unnecessary complexity.
Engineering support for the products you build
Our work is particularly relevant to engineering-intensive products where structural performance, durability or mechanical behaviour matters.
- Industrial equipment & machinery — structural assessment, nonlinear behaviour, fatigue, vibration, stability, failure investigation
You do not need to know in advance which simulation method you need.
Tell us what is happening, what you already know, and what decision you need to make. We can then determine what analysis, evidence or engineering work is actually justified.
Working across India