KonxisEngineering
Insights

Engineering insights

Practical articles on analysis, failure investigation and verification — including when advanced simulation is necessary, when it is not, and how to tell whether an engineering result can actually be trusted.

Featured articles
Analysis

8 min read
Konxis Engineering
2026

All articles

Why FEA results can be misleading

A converged solution is not automatically a correct engineering answer.

Convergence is a numerical statement. It says the solver found a solution that satisfies the discretised equations to a tolerance. It says nothing about whether those equations describe the physical problem in front of you.

The common failure pattern is familiar: a model runs, the contour plot is smooth, stresses look plausible, and the result is accepted because nothing obviously went wrong. But a model can converge perfectly and still represent the wrong load path, the wrong constraint, or the wrong failure mechanism.

Three questions before a result is trusted

  • Is the load path right? Where the load actually enters and leaves the structure is usually decided by contact, preload and joint behaviour — not by the geometry alone.
  • Is the constraint real? A convenient symmetry plane or a fixed bolt face can suppress exactly the deformation that is causing the problem.
  • Is the quantity being read the quantity that matters? Peak nodal stress at a re-entrant corner is not a physical stress. It is a mesh-dependent number.

Each of these can be wrong while the solution still converges cleanly. The plot looks the same either way.

What makes a result evidence

A result becomes evidence when it has been challenged: mesh and convergence checks, sensitivity to boundary conditions and material inputs, equilibrium and hand-calculation sanity checks, and — where it exists — comparison against measurement.

The question is never “does it converge?” It is “what would have to be true for this answer to be wrong — and have we checked?”

That is the difference between running a simulation and doing engineering with it. The contour plot is the beginning of the argument, not the end of it.

More on verification & validation

Verification & validation

6 min read
Konxis Engineering
2026

All articles

What makes a simulation trustworthy?

What verification and validation can establish — and what they cannot.

Trust is not a property of a model. It is a relationship between a model, a specific use, and the evidence available to support that use.

Two distinct questions are usually mixed together. Verification asks whether the analysis has been set up and solved correctly — geometry, loads, boundary conditions, material inputs, mesh, convergence, numerical behaviour. Validation asks whether the model represents the real system adequately for its intended use.

What verification can establish

  • The equations being solved are the equations you intended to solve
  • The solution is numerically converged and stable against discretisation
  • The model satisfies equilibrium and passes hand-calculation checks
  • The conclusions are — or are not — sensitive to the uncertain inputs

What validation adds

Validation compares prediction against something independent: a component test, field measurements, strain data, vibration response, operating behaviour. The comparison is only meaningful if the intended use is stated first. A model validated for trend prediction has not thereby been validated for absolute life prediction.

What neither can establish: that the model answers a question nobody defined. Verification and validation confirm fitness for a stated use — they cannot tell you whether the use itself was the right one.

Confidence is graded, not binary

Our evidence ladder makes this explicit: assumed input, calculated result, simulation result, measured result, validated result, released design. Confidence increases as independent evidence increases — and not every project needs to reach the last rung. Stating where a result actually sits is part of the engineering.

A model is trustworthy when its limits are as well documented as its results.

See how this appears in the case studies

Methods

7 min read
Konxis Engineering
2026

All articles

When nonlinear analysis is actually necessary

How to decide when the physics requires nonlinear behaviour and when a simpler model is better.

Nonlinear analysis is not a higher level of engineering. It is a specific response to a specific physical nonlinearity. The method should follow from the behaviour the answer depends on.

Four questions that decide it

  • Does the load path change with load level? If contact opens, closes or slips during loading, the structure is a different structure at each increment.
  • Does the material respond proportionally? Yielding, plasticity, hyperelasticity and damage mean stress is no longer proportional to strain.
  • Do displacements change the loading? Large deformation alters geometry, equilibrium and — in buckling problems — whether equilibrium survives at all.
  • Does history matter? Fatigue, preload sequences, cyclic plasticity and impact all depend on what happened before the current step.

If the answer to all four is no, a linear model is not a compromise. It is the correct, proportionate tool — and it is easier to verify.

When simpler is better

A nonlinear model multiplies the ways to be wrong: contact definitions, convergence parameters, load stepping, material characterisation. Every one of those needs evidence. A complex model that cannot be verified does not outperform a simple model that can — it merely moves the uncertainty somewhere less visible.

Often the right sequence is staged: an independent hand calculation to establish scale, a linear model to find the critical region, then nonlinearity introduced only where the physics demands it.

The objective is not the most complicated model. It is a model and evidence base that are appropriate for the decision.

Sometimes the right conclusion is that a more complicated analysis is not necessary. Saying so is part of the job.

Advanced structural analysis

Next step

Have a simulation you are not sure about?

You do not need to know which analysis method you need. Tell us what is happening, what you already know, and what decision you need to make.